Last visit was: It is currently Sun Jun 25, 2017 12:24 am


All times are UTC - 5 hours




Post new topic Reply to topic  [ 23 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject: Re: Adding Brultech Devices to EmonCMS
PostPosted: Mon Mar 13, 2017 4:52 pm 
Registered users

Joined: Sun Mar 12, 2017 7:45 pm
Posts: 16
Ok, went to Data Post and clicked dashbox/Standalone software. It puts the URL extension mentioned before in, so I removed it. Saved it, went to Packet Send and clicked Show Packet. Below is the packet, still not getting values on EmonCMS. Could it be hanging up on the "apikey=&node=" section?

GET ?apikey=&node=&json={SC:1062,V:0,E1:4474536,P1:0,E2:17335,P2:0,E3:2348,P3:0,E4:1843,P4:0,E5:1744,P5:0,
E6:1099,P6:0,E7:31,P7:0,E8:74895,P8:0,E9:389860,P9:0,E10:748,P10:0,E11:200509,P11:0,
E12:69,P12:0,E13:897,P13:0,E14:1602477,P14:0,E15:7816,P15:0,E16:39249,P16:0,E17:30670,
P17:0,E18:67,P18:0,E19:64935,P19:0,E20:280965,P20:0,E21:9217,P21:0,E22:14,P22:0,
E23:382841,P23:0,E24:24635,P24:0,E25:75735,P25:0,E26:4215,P26:0,E27:355803,P27:0,E28:0,
P28:0,E29:0,P29:0,E30:0,P30:0,E31:6217,P31:0,E32:35872,P32:0,C1:0,T1:nc,T2:x,T3:x,T4:x,
T5:x,T6:x,T7:x,T8:x,X:0} HTTP/1.1 Host: 192.168.143.158

Also, I gave the EmonCMS raspberry PI another reboot. Its not a raspberry pi 3, if that makes any difference.


Top
Offline Profile  
 
 Post subject: Re: Adding Brultech Devices to EmonCMS
PostPosted: Wed Mar 15, 2017 9:33 am 
Site Admin
BrulTech Staff

Joined: Fri Jun 04, 2010 9:39 am
Posts: 2794
brassfly wrote:
Ok, went to Data Post and clicked dashbox/Standalone software. It puts the URL extension mentioned before in, so I removed it. Saved it, went to Packet Send and clicked Show Packet. Below is the packet, still not getting values on EmonCMS. Could it be hanging up on the "apikey=&node=" section?

GET ?apikey=&node=&json={SC:1062,V:0,E1:4474536,P1:0,E2:17335,P2:0,E3:2348,P3:0,E4:1843,P4:0,E5:1744,P5:0,
E6:1099,P6:0,E7:31,P7:0,E8:74895,P8:0,E9:389860,P9:0,E10:748,P10:0,E11:200509,P11:0,
E12:69,P12:0,E13:897,P13:0,E14:1602477,P14:0,E15:7816,P15:0,E16:39249,P16:0,E17:30670,
P17:0,E18:67,P18:0,E19:64935,P19:0,E20:280965,P20:0,E21:9217,P21:0,E22:14,P22:0,
E23:382841,P23:0,E24:24635,P24:0,E25:75735,P25:0,E26:4215,P26:0,E27:355803,P27:0,E28:0,
P28:0,E29:0,P29:0,E30:0,P30:0,E31:6217,P31:0,E32:35872,P32:0,C1:0,T1:nc,T2:x,T3:x,T4:x,
T5:x,T6:x,T7:x,T8:x,X:0} HTTP/1.1 Host: 192.168.143.158

Also, I gave the EmonCMS raspberry PI another reboot. Its not a raspberry pi 3, if that makes any difference.


Been awhile since I last looked at this stuff.

Found some instructions on page 1:

Under "Data Post" fill out the following:

- URL Address: RPi IP Address (eg. 192.168.2.222)
- URL Extension: /emoncms/input/post.json
- Token: Read & Write Input API Token
- Node: If using the Device Module in the original Post, use the same Node Name you defined in Device Setup.
- The rest aren't used.

Extension may change based on whether or not you have a sub folder.

_________________
Ben
Brultech Research Inc.
E: ben(at)brultech.com


Top
Offline Profile  
 
 Post subject: Re: Adding Brultech Devices to EmonCMS
PostPosted: Thu Mar 16, 2017 6:42 pm 
Registered users

Joined: Sun Mar 12, 2017 7:45 pm
Posts: 16
I followed the instructions, but I was still not getting any values. I was getting on the Input Page I was getting NULL as my value. It dawned on me, could it be the port. Went to the GEM network utility, and changed the server IP to my raspberry, and the port to 80. Saved and now getting values.

Now just to get my EmonCMS setup to graph!


Top
Offline Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 23 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Theme created StylerBB.net & kodeki