• Male-Female Outlet adaptor with Loop for Split-Core or Clamp-On CT Access to Line Conductor
• One WPA-3 is included in the ECM-1220 PKG, however, and additional WPA-3 is required for monitoring two wall-plugged loads at the same time.

SPLIT-15 Split Core Current Transformer

• 15A. Max Split-Core CT is recommended for "low current" applications.

• Special Order

• 60A. Max Split-Core CT is the standard CT. One SPLIT-60 is included in the ECM-1220 PKG. For most 240V split-phase loads, a second SPLIT-60 is required, for loads of 60 A. or less.

• OUTPUT: 333mV @ 60A

• TERMINATION: 3.5mm stereo phone plug, tip (+), ring (-), sleeve NC.

• CABLE:  Between 5 and 6 Feet

• ACCURACY: +/- 1% from 5A to 55A

NOTE: The SPLIT-60 is NOT compatible with models ECM-1200, ECM-400, ECM-200si, ECM-200B and ECM-200. These units use CT-60 current transformer which is available as a special order. Quantity is limited.

• 100 Amp Split Core CT is ideal for permanent or long term monitoring of 100A service panels or loads.
• The split core type CT is preferred over the clamp-on style for permanent installations because of its size and lower cost.
• OUTPUT: 333mV @ 100A
• TERMINATION: 3.5mm stereo phone plug, tip (+), ring (-), sleeve NC.
• CABLE:  3 Feet, 300V Rating
• ACCURACY: See CT-200 Specification Sheet Graph

• 200 Amp Split Core CT is ideal for permanent or long term monitoring of 200A service panels or loads.
• The split core type CT is preferred over the clamp-on style for permanent installations because of its size and lower cost.
• OUTPUT: 333mV @ 200A
• TERMINATION: 3.5mm stereo phone plug, tip (+), ring (-), sleeve NC.
• CABLE:  3 Feet, 300V Rating
• ACCURACY: see Specification Sheet

SPLIT-200 Specifications

• 100 Amp Clamp-On CT is ideal for field applications where various loads are to be monitored. Because of its design, the CLAMP-100 is much easier to install and remove than the split -core type CT.
• OUTPUT: 333mV @ 100A
• TERMINATION: 3.5mm stereo phone plug, tip (+), ring (-), sleeve NC.
• CABLE:  6 Feet, 300V Rating
• ACCURACY: see Specification Sheet

CLAMP-100 Specifications

• 200 Amp Clamp-On CT is ideal for field applications where various "hi current" loads are to be monitored. Because of its design, the CLAMP-200 is much easier to install and remove than the split-core type CT.
• Not recommended for low current application due to decreased accuracy at low current.
• OUTPUT: 333mV @ 200A
• TERMINATION: 3.5mm stereo phone plug, tip (+), ring (-), sleeve NC.
• CABLE:  6 Feet, 300V Rating
• ACCURACY: see Specification Sheet

• 200A CT
• unlike the "split-core" and "clamp-on" style CTs, the "donut style" CT requires disconnection of load wire so that it can be threaded through the center of the CT.
• Generally only for permanent installation.
• Very accurate

CT "series connecting" Y splitter for connecting two matching CTs to one channel. For 333mV CTs only

Soon

• 6ft extension for CTs

• This voltage converter is used for certain 240V applications. It is used to power the wall transformer in situations where no 120V access is available.
• INPUT: 240VAC
• OUTPUT: 120VAC

• Blue polypropylene/nylon  with foam insert
• Metal Core Hinges
• Nylon Latches
• 12.75" x 9.25" x 4.56" (324mm x 235mm x 116mm)

• Blue polypropylene on with foam insert
• 12.75" x 9.25" x 2.625" (324mm x 235mm x 67mm)

• Additional Memory Storage "IC chips"
• Must be installed at the factory.
• Available in increments of additional 13,107 records
• Maximum memory: 52,401 records

• An additional Dongle is available to provide a second computer access to ECM-1220 -X models.
• Also performs "routing" function to provide mesh network "hopping".